SWR Pipe for Rainwater Downpipes and Terrace Drainage: Choosing Type, Size, Fittings and Fixing

November 13, 2026

SWR Pipe for Rainwater Downpipes and Terrace Drainage: Choosing Type, Size, Fittings and Fixing
Published: November 13, 2026 By: Trity Pipes

A rainwater system sits idle for most of the year and then has to work perfectly for twenty minutes. In a monsoon cloudburst, a terrace can shed a huge volume of water in a very short time, and if the downpipes cannot carry it, water backs up on the terrace, finds cracks, seeps into ceilings and damages walls. Those downpipes also live outdoors, in the sun, for decades.

That makes rainwater pipe a different job from soil and waste drainage inside a building. This guide explains how to choose SWR pipe for terrace and roof drainage: which pipe type to use, how to size outlets and downpipes, which fittings you need, how to deal with sun and thermal movement, how to fix pipes to walls and how to order from Trity Pipes. For the indoor side, read our guides on SWR pipe sizing for multi-storey buildings and Ringfit vs Selfit.

Keep rainwater separate from soil and waste

Rainwater should have its own stack and its own drain. It should not be connected to the soil and waste stacks inside the building, because a heavy downpour could overload the sewage system and force water back up into bathrooms. Rainwater is sized by the area of the roof and the local rainfall intensity, not by the number of fixtures, which makes it a different calculation from sanitary drainage. Plan the rainwater system as a separate network, discharging to a storm drain, a soak pit, a harvesting system or as the authorities require.

Which SWR pipe type for rainwater

Trity makes SWR pipes in Type A and Type B. Type A is used for ventilation and rainwater lines, and Type B for soil and waste discharge. For terrace and roof drainage, Type A is the usual choice, and Type B is used where the specification calls for it. Type A has a thinner wall than Type B for the same diameter, so check the type on every line of a quotation. Our guide on how to check SWR pipe quality explains how to measure wall thickness and confirm the type.

Ringfit or Selfit for downpipes

Both systems work for rainwater pipes.

  • Ringfit uses a rubber ring joint, which accommodates thermal expansion in long vertical runs and goes together quickly, which is useful on tall buildings where working at height is slow.
  • Selfit uses solvent cement, which makes a permanent joint and suits shorter runs and fixed layouts.

Many projects use Ringfit for tall vertical stacks and Selfit for short branches. Our guide on Ringfit vs Selfit explains how to choose.

Sizing outlets and downpipes

The size depends on the roof area drained and the design rainfall intensity for your location. Engineers use the plumbing code and local rainfall data, and our role is to supply the pipe. As a general guide:

  • Small terraces and sunshades often use 75mm to 90mm
  • Typical house and apartment roofs commonly use 90mm to 110mm
  • Large roofs, podiums and commercial buildings use 110mm and above, with 160mm and 200mm for main collection and horizontal runs

Do not size by habit. A terrace that drains too slowly floods, and a downpipe that is too small for a large roof is a common cause of leaks. Use the design from your consultant, and if you are unsure, ask our technical team for guidance with your roof area and location. Our guide on SWR pipe sizing for multi-storey buildings covers rainwater stacks as part of the wider drainage design.

Fittings for terrace drainage

A rainwater system needs more than straight pipe.

  • Outlets and drain points at low points of the terrace, with gratings or domes to keep leaves and debris out
  • Bends to turn the pipe from the outlet into the downpipe, and offsets where the pipe must clear structure. Two 45-degree bends flow better than one sharp 90-degree bend
  • Junctions where several outlets join a common line
  • Reducers and couplers
  • Access and cleaning fittings so that blocked lines can be cleared
  • Shoes and bends at the base to direct water into the drain or chamber

Our guide on SWR fittings explains each fitting and how to count them. Ask our team which fittings are available in your diameters.

Sun, UV and thermal movement

Downpipes sit on external walls in direct sun, and they heat up and cool down every day.

  • UV exposure. Our product page describes Trity's SWR pipes as UV stabilised for outdoor exposure. For exposed rainwater lines, confirm UV stabilisation with the supplier in writing, since ordinary pipe can chalk and become brittle in strong sun.
  • Thermal expansion. A long vertical downpipe expands and contracts. Use expansion-tolerant joints and fix the pipe so that it can move at the sockets, instead of clamping every point rigidly.
  • Colour. Pipe that heats less is gentler on joints, and many buildings paint exposed pipes to match the facade, using a paint that is suitable for the pipe material.

Fixing downpipes to walls

  • Use proper clamps that grip without crushing the pipe
  • Space clamps at distances that stop sagging and rattling, and fix a clamp near each socket
  • Keep the pipe straight and plumb
  • Allow movement at sockets for expansion
  • Protect the base from impact by vehicles or trolleys where the pipe is accessible, with a guard or a stronger section
  • Seal the penetration where the pipe passes through a parapet or a slab, so water does not leak around it

Common problems and how to avoid them

  • Blocked outlets. Leaves and debris block terrace outlets. Fit gratings and clean before the monsoon.
  • Undersized downpipes. Size from roof area and rainfall, not guesswork.
  • Leaking joints. Clean Ringfit sockets and seat the ring properly, and apply Selfit cement evenly with full cure time.
  • Sagging pipes. Use enough clamps.
  • Connecting to the sewer. Keep rainwater separate from soil and waste.
  • UV-damaged pipe. Use UV-stabilised pipe on exposed runs.
  • No access points. Add cleaning fittings at bends and the base.

Rainwater harvesting

Many buildings now collect roof water in tanks or recharge pits. Rainwater pipe feeds a filter or first-flush device and then a tank or a recharge structure. Size the pipe for the roof's peak flow, and fit access for cleaning, because harvesting systems clog if debris enters. Where water from a roof is connected to storage, check local rules and keep the system separate from drinking water supply.

Testing the system

Before you close up or paint, run water through the outlets to check flow and joints, look for leaks at every joint and clamp, and check that the terrace slopes to the outlets, since a flat terrace that holds water will test the system on every rainy day. Our guide on SWR pipe installation covers jointing practice in detail.

Ordering for a project

  • List outlets, downpipes and horizontal collectors from the drainage drawing, by diameter and type
  • Count fittings and add spares
  • State the joint system for each line
  • Confirm UV stabilisation for exposed runs
  • Ask for documents such as certification and test reports
  • Phase delivery to follow construction, since rainwater lines go in late on tall buildings

Our guide on SWR pipe price explains the cost factors and how to compare quotations.

Why builders and plumbers choose Trity SWR pipes

Trity Pipes manufactures SWR pipes and fittings in Ringfit and Selfit systems, from 40mm to 315mm, to IS 13592, with ISO 9001:2015 certification and quality checks at each stage of production. We offer Type A and Type B pipes, matching fittings so that the whole drainage system can come from one manufacturer, and certification documents on request. Our team can help you choose type, joint system and sizes for your rainwater lines. See the full SWR pipes and fittings range. Builders can ask for bulk and phased supply, and dealers can ask about stocking the range.

Frequently Asked Questions

Which SWR pipe type is used for rainwater downpipes?

Type A is the usual choice for ventilation and rainwater lines, and Type B is used for soil and waste. Check the type on every quotation and follow your project specification.

What size downpipe do I need for a terrace?

It depends on the roof area and design rainfall intensity. Small terraces often use 75mm to 90mm, typical roofs 90mm to 110mm, and larger roofs 110mm and above. Follow the design from your consultant.

Can I connect rainwater downpipes to the sewer line?

Keep rainwater separate from soil and waste drainage inside the building, and discharge it to a storm drain, soak pit or harvesting system as local rules require.

Does SWR pipe need to be UV stabilised for outdoor use?

Exposed downpipes see strong sun, so UV-stabilised pipe is recommended. Our product page describes Trity SWR pipes as UV stabilised, and you should confirm it in writing with any supplier.

How do I stop rainwater downpipes from sagging or leaking?

Use proper clamps at suitable spacing, fix a clamp near each socket, allow movement at sockets for expansion, and make sure joints are clean and fully seated or cured.

Can Trity Pipes supply rainwater pipes and fittings in bulk?

Yes. Share your diameters, types, joint system and quantities, and our team will prepare a quotation and discuss phased delivery from our Delhi NCR factory.

Planning terrace and roof drainage? Contact Trity Pipes on +91-9821030072 or +91-9319984755 for an SWR pipes and fittings quotation, UV and type guidance and certification documents from our Delhi NCR factory.

Trity Pipes  |  November 13, 2026

Back to Blogs

Ready to Order? Get a Free Quote Today!

Our team is ready to assist you with product selection, pricing, and technical support.